Crystal Cote 350 – U35

RESOURCES:

pdf_iconlargeEnglish Spec / Data Sheet
pdf_iconlargeEnglish SDS Sheet

AVAILABILITY:
108865: 5 Gallon pail

Categories: , , SKU: u35

Description

Crystal Cote 350
VOC Compliant Polyurethane Wood Finish

FEATURES:
• Rich Gloss
• Meets Maximum VOC

BENEFITS:
• Floors Look excellent
• Low Odor
• Guarantees quality & performance

AREAS OF USE:
• Wood Floors
• Colleges
• High Schools

DESCRIPTION
Oil modified polyurethane finish designed for use on sports, commercial, and residential wood floors. Produces outstanding durability and resistance to scuffs, spills and stains. Leaves surface with an extremely rich gloss that dirt and grime can’t penetrate. This product meets the strict VOC (Volatile Organic Compounds) requirements, which have been established in many states throughout the country. Easy to apply, it is compatible over a wide variety of conventional solvent-based coatings (provided these coatings are cured, bonded and the floor is properly prepared).

DIRECTIONS
On previously coated floors:
A test patch is strongly recommended to determine adhesion compatibility over a previous finish/sealer.
Remove any masking tape or gum with a putty knife. Clean the floor of dirt, dust mop treatments, etc. with a neutral cleaner. Allow the floor to dry thoroughly. Screen the floors with #100 grit screens (250 sq. ft. per side; 23m2) until the gloss is removed. Tack rag the floor using waterless cleaner. Apply finish going with the grain using a conventional lamb’s wool or foam applicator or weighted T-bar applicator. Do not allow the finish to puddle. Allow 48 hours cure before light traffic and 5 – 7 days before athletic activities. Adequate ventilation is imperative during the curing process. Dry times will vary based upon the drying conditions. Do not apply when temperature is above 95° F (35°C) or below 65° F (18°C), or when humidity is above 80%. Clean up with waterless cleaner.

Newly installed floors or sanded to bare wood:
Screen the floor using #100 grit screens (250 sq. ft. per side, 23m2). Vacuum then tack rag the floor with a quality waterless cleaner. Allow the floor to dry to a dull, glossless surface.

Seal coat application:
Seal the bare wood with a quality polyurethane sealer using a conventional lamb’s wool, foam applicator, or weighted T-bar. Minimum of two coats of sealer is recommended. Following the directions for that product. Allow to dry thoroughly. Remove raised grain with a #120 grit screen, then tack rag with a quality waterless cleaner. Line marking paint can then applied.

Finish coats application:
Apply finish going with the grain using a conventional lamb’s wool, foam applicator, or weighted T-bar applicator. Do not allow the finish to puddle. Allow 48 hours cure before light traffic and 5 – 7 days before athletic activities. Adequate ventilation is imperative during the curing process. Dry times will vary based upon the drying conditions. Do not apply when temperature is above 95° F (35°C) or below 65° F (18°C), or when humidity is above 80%. Clean up with waterless cleaner.

Manufacturer’s Recommendation: This coating is to be applied without thinning.
VOC Content < 350 grams/liter

SPECIFICATIONS:

Type Low VOC oil modified urethane varnish
Color Light Amber
Odor Solvent
pH N/A
Non-Volatile Solids 50%
Coverage 400 – 800 sq.ft./gal.
Recommended Coats 2 coats
Compatibility Solvent-based urethane varnish
Dry / Recoat Time 16 – 36 hours
Viscosity A1 – A ASTM D1545
VOC Content < 350 g/l
Removability Sanding
Flashpoint 105 0F ASTM D56
Storage/Stability 2 years
Weight per Gallon 7.58 lbs./gal.
Store Condition 40 – 90 0F

 

Additional information

Finish Type